CV Sr Piping Engineer Greater Ekofisk Modification Project Norway ANSI ASME 31 NORSOK ARAMCO standards

Resume built for oil and gas job opportunities by a jobseeker with experience in Sr Piping Engineer Greater Ekofisk Modification Project Norway ANSI ASME 31 NORSOK ARAMCO standards - would you like to offer this candidate a job/contract employment?

CV/Resume ID no.: 106817
Last Updated: Tuesday, March 2, 2010

Key Qualifications:

Main Discipline: Lead Piping Engineer, Structural Designer, Piping Layout, Piping Stress
Engineer, Pipe Support Engineer, PDMS Piping Designer


16 years experience of Piping Engineering including 2+ years of experience in Greater Ekofisk Modification Project, Norway, almost 10 years experience as Lead Piping Engineer, 4 years as Sub-Group Leader, with experience in the actual construction and Pipe Installation at site. Familiar with international codes & standards (JIS, ANSI, ASME 31, NORSOK, ARAMCO and BS Standards).

Dec. 2009 – present

Saudi Consulting and Design Office (SCADO)
Al Khobar, Saudi Arabia

Position: Senior Piping Engineer

Project Undertaken:

Ethylene Vapor Pipeline
Saudi Kayan Petrochemical Company
Jubail, Saudi Arabia

Prepare Piping Stress Analysis by CAESAR II computer software, Piping Plan and Piping Isometric Drawing. Prepare Nozzle Calculation and Adequate reinforcement Pads on Tanks, Pressure Vessel and Columns. Prepare Hydraulic Impact Analysis on Flooded & Lift Suction lines and Discharge of Pumps. Prepare suction and discharge calculation on Control Valves.

March 2007 – Oct. 2009

Fabricom Suez AS
Stavanger, Norway

Position: Piping Engineer

Project: Greater Ekofisk Modfication Project
Conoco Phillips
North Sea, Norway

Prepare Gaslift and Flowlines offshore piping design/layout, pipe support design in 2D and 3D, Piping Arrangement Drawing and composite drawing. Prepare the Piping Stress Analysis by CAESAR II computer software and in Isometric Model. Check the piping isometric drawing and MTO. Prepare the final output as-built 3D model, input additional information and UDA before submission to client.
October 1997 – March 2007

IHI Philippines, Inc.
(A design company managed by I H I Corporation, Tokyo, Japan)

Position: Lead Piping Engineer

Projects Undertaken:

• Sonatrach-Blanche AVAL-Division EDV-Oran, Algeria
Sonatrach LPG Plant Modification Project
April 2005 – Feb. 2007
Responsible but not limited to Participate on the Survey of the existing Plant, prepare recommendations and improvement for the increase of the efficiency and to shorten the time the plant shuts down on its operation. Prepare Pipe Stress Analysis, Prepare Piping Design/Layout model in 3D. Piping Isometric Drawing, location and layout of Pipe Supports from the result of Pipe Stress Analysis and MTO. Make Piping Support Detail Design and Material selection.

• Chinese National Petroleum Company- Taipei, Taiwan
• Saibu Gas Refinery Plant - Saibu, Japan
June 2002 – March 2005
Responsible for the Piping Design Schedule, but not limited to plan, direct and coordinate a successful development of the project, preparation of Man-hour estimation, control of man-hour consumption, schedule control, workload distribution. Design/layout of Piping Plan Drawing, Piping Isometric Drawing and MTO, pipe support location, layout and detail design. Preparation of 3D model of the project, arrangement of pipelines, pipe fittings, tie-ins, equipment arrangement, cable trays, piping supports considering the results of the Pipe Stress Analysis.

• Kiln No.2 Project Sharjah Cement Factory, Sharjah, U.A.E
August 2001 – May 2002
Responsible but not limited to Supervise directly and indirectly to the construction team, contractors of the Installation of Pipes and Piping Component of Pre-Heater Tower, Ducts and Diaphragm Valves, Fire fighting pipelines. In charge of the design and layout of additional pipelines, sub-structure and Pipe Supports Detail Design and MTO.

• Altamira LNG Terminal -Tamaulipas, Mexico
May 2001 – July 2001
Responsible for the Piping Design Schedule, but not limited to plan, direct and coordinate a successful development of the project, preparation of Man-hour estimation, control of man-hour consumption, schedule control, workload distribution. Design/layout of Piping Plan drawing, piping isometric drawing and MTO, design pipe support location, layout and detail design. Preparation of 3D model of the project, arrangement of pipelines, pipe fittings, tie-ins, equipment arrangement, cable trays, piping supports as considering the results of the Pipe Stress Analysis.

• High Technology Fatty Alcohol Project, Pilipinas Kao Corp.
May 2000 – Apr.2001
Responsible but not limited to Supervise directly and indirectly to the construction team, contractors of the installation of pipe spool and piping component of the new distillation and fractionating towers. Checking and trace actual fabricated pipe spool. Issue and implement approve punch list and deficiency on the construction.

• Ras Laffan Qatar Gas LNG Terminal –Doha, Qatar
• Hokkaido Gas Co. Ltd., Hakodate Sector – Hokkaido, Japan
Oct 1997 – April 2000
Responsible for the Piping Design Schedule, but not limited to plan, direct and coordinate a successful development of the project, preparation of Man-hour estimation, control of man-hour consumption, schedule control, workload distribution. Design/layout of Piping Plan, piping Isometric drawing and MTO, designate appropriate pipe support location, layout and detail design. Preparation of 3D model of the project, arrangement of pipelines, pipe fittings, tie-ins, equipment arrangement, cable trays, piping supports as considering the results of the Pipe Stress Analysis. Coordinate, inform and check client's data and vendor's available material on the detailed fabrication drawing of piping isometric drawing, Steel structure, piping components and pipe supports.

Oct. 1995 – Sept. 1997

Dash Engineering Philippines
(Subsidiary of Mitsui Engineering & Shipbuilding, Tokyo, Japan)

Position: Sub-Group Leader

Project Undertaken:

• Kuwait National Petroleum Co. - Al-Ahmadi, Kuwait
• Petrochemical Corporation of Singapore, Singapore
Responsible but not limited to prepare Pipe Stress Analysis, Piping Arrangement Drawing, Piping Isometric Drawing, MTO and Layout of Pipe Support based on Piping and Instrumentation Diagram and Engineering Flow Diagram. Checking of pipeline clashing, material selection, issuing back drafts and coordinate other Engineers and Disciplines.

Education
• 1985 – 1990 Bachelor of Science in Electrical Engineering
Technological Institute of the Philippines - 1990
Manila, Philippines
IIEE Member, May 1993 - present
Registered Electrical Engineer, License No. 26460
Passed the National Licensure Examination

Training/Course
• 1998 PDMS Training Course
• 1999 AOTS (The Association for Overseas Technical Scholarship)
Detail Design for Piping Arrangement Drawing
Detail Design for Piping Isometric Drawing
• 2001 Leadership Training
• 2007 SAP Course
• 2007 PROARC Course

• PDMS
• Microstation v.8
• Autocadd (all version) in 2D, 3D & Autolisp Programming
• Autopipe
• CAESAR II
• Staad Pro
• XSteel
• Magan for 3D Survey
• SAP
• PROARC
• MS Office, Word, Excel, Outlook, etc

None