CV CAD Designer, International Oil and Gas HSE certificate holder and an Authorized Gas Tester

Resume built for oil and gas job opportunities by a jobseeker with experience in CAD Designer, International Oil and Gas HSE certificate holder and an Authorized Gas Tester - would you like to offer this candidate a job/contract employment?

CV/Resume ID no.: 119002
Last Updated: Thursday, March 17, 2011

Dear Sir/Madam,

I wish to apply for any vacant position in your company that best suites my working background and profession.

I am 29 years old, single, and an electronics engineer. I am also an International Oil and Gas HSE certificate holder and an Authorized Gas Tester.

I believe that your organization has the capacity to further advance my career. I pride myself in adapting successfully to changing and challenging environments including working both autonomously and in team situations, in which I enjoy. In regards to my work ethos, working under pressure I consider, as one of my underlying strengths. As a potential employee I am receptive to new ideas and thoughts and always keep an open mind.

HIGHLIGHTS:

 Risk assessment based on OHSAS 18001 prior to carrying out critical and hazardous
tasks.
 Review of safety manuals for updating, safe practices & emergency plans and
procedures, risks & crises management incorporating statutory requirements and
recognized international standards.
 Knowledge in operation/use of oil and gas fire fighting (i.e., FP70 mechanical base
foam injection, portable & mobile fire extinguishers, N2 activated AFFF, fire tenders,
RIV) and life saving equipment (e.g., SCBA & refill system, escape set/mask)
 Sound knowledge of Material Safety Data Sheets (MSDS) & Control of Substances
Hazardous to Health (COSHH).
 Safety audits, accident investigation and report writing.



SUMMARY OF QUALIFICATIONS

• International Oil and Gas HSE Certificate
• Authorized Gas Tester
• Registered Electronics and Communications Engineer (ECE - 41444)


WORK EXPERIENCE
September 2009 – November 2010 MEP Cad Operator
Denver Engineering and Contracting Company WLL, Doha, Qatar

Job Description Worked in a MEP Contracting Company as a CAD operator/designer handling high-rise building projects like Jude Tower, Tornado, and Al-Khor Mall in Qatar.

 Designed Fire Fighting Layout for Al-Khor Mall department store that has been approved by the consultant for construction.
 Prepared almost all electrical shop drawings for construction as per request of the end-user.
 Assists the mechanical engineer to make the riser diagram layout of
AC ducting.

January 2007 – April 2009 Instructor of Autodesk AutoCAD 2006-2009
Crescent Technologies Institute, an Autodeskฎ Authorized Training Center

Job Description Worked in an Autodesk Authorized Training Center as an instructor that trains architects, engineers, draftsmen and other professionals on the fundamentals of 2D and 3D computer-aided drafting and color/material rendering using Autodesk AutoCAD software.

 Taught Autocad 2007 to engineers of various companies like Fujitsu and Ford.
 Done Architectural/Structural Projects from private individuals/firms for computerization.

May 2006 - December 2006 Communications Engineer
Netbridge Broadband Information Power Communications Corporation, Philippines

Job Description Worked in a contractor for voip networks of a telecommunications company.

 Coordinated with the carriers' communications engineers for the installation and activation of the service for the clients.
 Installed, tested and commissioned the voice and data network of our company's clients.
 Worked with a team of professionals on an installation, testing and commissioning of value added services in a telecommunications project in which the duties assigned primarily involve project management and production of graphical illustrations for presentation of materials and reports.
 Also worked as a Technical Sales and Support Manager handling multiple subordinates for a contract-selling venture.

2010 International Oil & Gas HSE Certificate
Offshore Onshore Oil & Gas HSE Training Center and Career Development
( IADC & IOSH Affiliate )
East Ortigas Mansions, Pasig City, Philippines

 Basic Oil and Gas Process
 Introduction to Oil Platforms, Derrick Barges and Jack-up Rigs
 Basic Water and Gas Injection
 Oil and Gas Separation (Two Phase and Three Phase)
 HSEMS Based on OHSAS 18001
 Base Foam Injection for Crude Oil Tank
 Christmas Tree and Two Barrier Rule
 Liquefied Natural Gas (LNG) Safety
 Safety Orientation for Offshore Platforms Installation
 Basic Pigging Operations
 Fatal Accidents in Oil and Gas
 Confined Space & Vessel Entry
 Lifting Safety and Color Codes
 Pipeline Intervention (Hot Tapping, Line Freezing)
 Techniques in Working Flammable Atmosphere, Safe house Habitat
 Floating Roof Tank Cleaning & Simultaneous Recovery
 Basic Oil Spill Calculation
 Compressed Gas Cylinders Safe Distance
 Permit to Work System (PTW) and Compliance Audit
 Hydrogen Sulfide (H2S) Course
 EPIRB Induction
 Noise Awareness (Logarithmic Computation & NRR)
 Actual Training SCBA
 Risk Assessment in the Oil & Gas Production Platform & Well head Towers
 Propane and BLEVE
 Static Electricity
 Personal Protective Equipment ( PPE) in the Oil & Gas Industry
 Accidents Investigation & Analysis of O&G Accidents
 Authorized Gas Tester Course
 Fire Extinguisher Course
 Ozone Depletion
 MSDS/COSHH
 Low Specific Activity/ NORM
 Offshore/Onshore Pipeline Construction

2010 Authorized Gas Tester Course
Offshore Onshore Oil & Gas HSE Training Center and Career Development
( IADC & IOSH Affiliate )
East Ortigas Mansions, Pasig City, Philippines

2005 Bachelor of Science in Electronics and Communications Engineering
University of Mindanao
Matina, Davao City, Philippines

• Proficient skills with Autodesk AutoCAD Releases 2000-2010
• Trained in Computer Aided Construction Project Management Using Primavera 3
• Has good knowledge on Linux operating system particularly Ubuntu distribution.
• Full range of spreadsheet and word-processing skills (MS Office: MS Word, MS Excel, MS PowerPoint; Windows applications) and picture editing software like Photoshop and Gimp (an open-source image editing program)

SPECIAL TRAININGS ACQUIRED

2007 Computer Aided Construction Project Management using Primavera 3
Crescent Technologies Institute, Sampaloc, Manila, Philippines

2006 AutoCAD for the Professional Level 1 & 2
Crescent Technologies Institute, Sampaloc, Manila, Philippines

2004 Cabling System
University of Mindanao, Matina Campus, Davao City, Philippines

PIC – Microcontroller Seminar/Workshop
University of Mindanao, Matina Campus, Davao City, Philippines