CV Mechanical Technician Oil & Natural Gas Corporation ONGC, Mumbai Offshore India, SABIC Saudi Arabia

Resume built for oil and gas job opportunities by a jobseeker with experience in Mechanical Technician Oil & Natural Gas Corporation ONGC, Mumbai Offshore India, SABIC Saudi Arabia - would you like to offer this candidate a job/contract employment?

CV/Resume ID no.: 119763
Last Updated: Monday, February 7, 2011

Professional Objective:

Diploma holder in Mechanical Engineering from State Board of Technical Division with over 7 years of experience & also studying B.TECH (Mechanical 3rd year student).

Experience in maintenance of major rotating equipment: Gas & Steam Turbines, compressors, pumps, diesel engine, fans and blowers etc. leading the team of technicians in overhauls / servicing. Exposure of pre commissioning / commissioning of rotating equipment in Oil & Gas plants. Exposure on mechanical seal, bearings, fits & tolerances, alignment of rotating equipment with laser alignment methods and measuring instruments.

EXPERIENCE SUMMARY

M/s Oil & Natural Gas Corporation ( ONGC), Mumbai. (Offshore)

(Through M/s. Spectron Engineers. Of Mechanical Maintenance)
Designation : Mechanical Technician
Period : June 2009 TO Till date


M/s Sabic, Saudi Arabia (Onshore)
Designation : Mechanical Technician
Period : March 2007 to MAY 2009 .


M/s Oil & Natural Gas Corporation ( ONGC), Mumbai. (Offshore)

(Through M/s. The Supreme Group Services. Of Mechanical Maintenance)
Designation : Mechanical Technician
Period : July2006 to Fep 2007.

M/s Oil & Natural Gas Corporation ( ONGC), Mumbai. (Offshore)

(Through M/s The Samfire Services. Of Maintenance contract)
Designation : Mechanical & Maintenance Technician
Period : June 2004 to June 2006.

M/s Oil & Natural Gas Corporation ( ONGC), Mumbai. (Offshore)

(Through M/s The Technomech Engineers. Of Maintenance contract)
Designation : Mechanical Technician
Period : May 2003 to May 2004.


EQUIPMENTS HANDLED:
Offshore experience:
• Operation of X-mas tree Crown valve, upper master, lower master, wing valve (operating closing), surface safety valve, and adjustable choke valve, SSSV/Down valve.
• Choke manifold, upstream by pass, positive choke valve, and down changing of chokes.
• Knowledge on flow lines, work of separator, conditions of test, production separator, 3phase separator (oil, gas & water), PCV, oil level controller, gas presser controller.
• Changing of orifice plate, taking separator reading, flowing well fluid through separator, by pass opening and closing of manual low valves.

Pumps:
Makes: Pacific, Sulzer, Sundyne, Uraca, Ebara, Flowserve & Nuovo pignone.
• Having relevant experience in maintenance in all types of pumps such as centrifugal, reciprocating & rotary pumps.
• Obtaining a complete check list of the dismantled equipment and keep a record of the same.
• Inspect the condition of rotating parts namely shaft, sleeve, impeller, oil deflectors, wearrings, bearings, coupling and stationary parts such as casing stuffing box, distance pieces and bearing housing.
• Renewal of mechanical seals replacement of rotor checking wearing and throat bushes, bearing clearances
• Maintaining the required Radial & Axial float in multistage pumps
• Checking the Stuffing box Squareness and concentricity using a dial gauge while pump assembly.
• Hydrotest of pumps to determine mechanical seal and casing leaks.
• Over hauling of reciprocating pump such as plunger pump & diaphragm pump including renewal of plunger packing, oil seals, suction discharge valves checking & servicing.

Mechanical seal:
Makes: John crane, Flowserve & Burgmann.
• Assembling, reconditioning and replacing all type of Mechanical seals such as single double, tandem and cartridge seals, having single, multi-spring and bellow type.
• Renewed seal faces (primary ring & mating ring) and maintained operating length lapping seal faces to the required finish.

Centrifugal compressor:
Makes: GE Oil & Gas (MCL1402, BCL803, BCL427), Sulzer, Kawasaki & Elliot.
• Completely overhauled GE (MCL1402, BCL427)
• Inspection, Dismantling & Installation of Thrust bearings and Journal bearings (plain and tilting pads types) with direct and pressurized lubrication systems.
• Locate position of rotor assembly and proper installation of gas seals or oil film seal.
• Respecting the Radial & minimum axial clearance between impellers and diaphragm and delivery dimensions of volute.
• Performing alignment between driver and driven units.
Alignment:
• Rim and face method
• Reverse indicator method
• Laser method

Reciprocating compressor:
Makes: Ingersoll Rand, Kirloskar
• Inspection, Dismantling & Assembling of Coupling, fly wheel, crank shaft, connecting rod, cross head, gudgeon pin, piston rod, piston and cylinder.
• Maintaining limited clearance of Main bearings, Big end and small end bearings with direct or pressurized lubrication systems.
• Refurbishment of suction & discharge valves, unloader & Renewal of cylinder liner
• Check and replace the piston rings, rider/guider rings, stuffing box packing & wiper rings
• Check and adjust the Cross Head Shoe Clearance, TDC & BDC
• Respecting the minimum deflection on piston rods
• Performing alignment of Compressor with driver Equipments.

Steam turbine & Gas Turbine
Makes: GE Oil & Gas & Nuovo Pignone, GE Oil & Gas (M9001E), solar gas turbines (Mars100)

• Completely overhauled Steam Turbine used for run Centrifugal Compressor.
• Inspection, Dismantling & Installation of Thrust bearings and Journal bearings (plain and tilting pads types) with direct and pressurized lubrication systems.
• Disassembling & Assembling of Rotor, Inner casing, stator blades, Oil and steam labyrinth seals, Mechanical Trip & Governor (PGPL).
• Servicing & Reinstalling of Emergency stop valves & Regulation valves assembly.
• Respecting the minimum safety axial clearance between rotor and stator.
• Performing Cold & Hot alignment of Steam Turbine with driven Equipments.
• Replaced the Turbine Nozzles & Buckets.

Static equipments:
• Maintenance jobs carried out in heat exchangers of fixed, floating and u tube type which include activities right from blinding, bundle pulling, cleaning, testing, repair works as per inspection etc.
• Maintenance jobs carried out in fin fan air coolers which include activities like blinding, plugs removal tubes id cleaning, hydro testing activities etc.
• Maintenance jobs carried out in replacing existing tower internals as per requirement.
• Maintenance jobs carried out in Column which include activities like removal of trays, demisters, packing, trays cleaning , etc.,
• Maintenance jobs carried out in absorber & vessels which include activities like cleaning, catalyst renewal, Demister removal etc.,
• Maintenance jobs carried out in filters which include activities changing of elements, cleaning, inspection clearance etc.,

Valves:
Servicing and testing valves like gate valves, globe valves, angle valves, ball valves, check valves, diaphragm valves, butterfly valves, pressure safety valve, pressure relief valve, crown valve, upper master, lower master, wing valve, SSV, choke & needle valve.

Safety:
• Follows all safety rules and guidelines established by the offshore, onshore and actively participates in safety meetings, safety programs.
• Having good knowledge in Permit to Work, Safe Job Plan/Job Safety Analysis, Material Safety Data Sheet, Tool Box talks and Hazards & Hazards control
• Imparts job knowledge & training to my team in the field.
• Understands and apply to plant safety standards and maintenance procedures while performing work

Professional Qualification:
Diploma in Mechanical Engineering (DME) - State Board of Technical Division. Govt. of Tamilnadu.

Bachelor of Technology (B.TECH) – Third year in Progress from Rajasthan Vidyapeeth University.

Academic Qualification:
Secondary School Leaving certificate (SSLC)

Computer Skills:
MS Office Packages.
AutoCAD

Safety Courses:
Personnel Survival Technique
Fire Prevention and Fire Fighting
Personal Safety and Socials responsibilities
Elementary First Aid
HUET