CV PDS/PDMS Piping / Electrical designer

Resume built for oil and gas job opportunities by a jobseeker with experience in PDS/PDMS Piping / Electrical designer - would you like to offer this candidate a job/contract employment?

CV/Resume ID no.: 75137
Last Updated: Thursday, October 7, 2010

To work with an Engineering procurement construction company that integrates a profound Professional attitude with the employee, with a friendly working environment and would give the opportunity for a better career advancement in the field of engineering and design department. I am seeking for a position in the organization which commensurate to my qualifications.
Over 18 years of extensive experience in the field of Engineering and Design for
Petrochemical / Chemical plants, polyethylene plants and Power plants


PDS. Designer in Electrical and Instrument dept. in Jacobs engg. Singapore I am a Singapore permanent resident. Totally I have 18yrs. Experience in MNC company like Bechtel, Technip, Chiyoda,
Foster wheeler and Jacobs Engg. I perform multiple disciplinary duties. I have 13yrs of piping designing experience in petrochemical and chemical plant, 5 yrs in E&I design in petrochemical and pharmaceutical experience I heard your company is hiring designers.

I have UK-NARIC Evaluation letter about my Education

I possess expertise knowledge in the following Software’s listed below
1. Plant Design System (PDS) over 9yrs.
a) Piping modeling, Equipment modeling,
b) EEraceway (electrical and Inst. Tray routing)
c) PD Draw pds 2d drawing using Drawing Manager
d) Microsation ver. J7, V8
2) Plant design management system (PDMS) over 3yrs.
a) Piping modeling, Equipment modeling,
b) EEraceway (electrical and Inst. Tray routing
c) HVAC in PDMS
3) Auto Cadd ver. 2000 to 2005
a) Auto cad 3d
4) Cad duct supporting software for auto plant
a) Cable tray routing and HVAC. Duct routing
5) Smart plant Review

JACOBS ENGINEERING SINGAPORE
Since August 2005 working as PDS designer in Piping and E&I dept.

Project and Responsibilities
Glaxo Smithkline R&D-Chemdev Pilot Plant Singapore.
Preparation of 3D Modeling in Electrical cable ladder and Instrument cable tray
For 1st storey to 6th floor over all cable ladder and tray sub-trays modeling, RJB modeling
Richo conduit drop and Mcc room, Dcs room equipment modeling using CADD duct softwear.
Preparation of Detail fabrication cable tray layouts.

Project and Responsibilities
HUNTSMAN SINGAPORE PLANT JAU-R
Preparation of over all PDS piping model small bore piping and Electrical and Instrument cable tray and ladder modeling Using PDS RACEWAY 3d Model and Lighting and Junction Boxes using PDS Equipment modeling.


FOSTER WHEELER, SINGAPORE
June 2001 to August 2005
Piping / Electrical PDS designer / PDS operator

Project and Responsibilities
Novartis Singapore Pharma Mfg.
Preparation of isometric, P&ID & Piping layout, Electrical Single line Diagrams
And Cable tray, Instrument Location plan drawings using AutoCAD & Micro station V8
On going Project.

Project and Responsibilities
Exxon Mobil Asia Pacific Singapore Transplus project
Piping Isometric and Piping Layout Preparation and Bill of material preparation
Using AutoCAD & Micro station V8.

Project and Responsibilities
MSD Pharma Mfg. (Singapore Ltd.)
Piping model, Equipment Model, Electrical, Instrument cable tray and conduit model
And Electrical Lighting using through PDMS.
Project and Responsibilities
Process scale-up facility for M/s Bristol-Meyers Squibb Company, USA.
Piping Routing & Equipment Modeling in PDS for Production Hall &
Manifold area.
Cable Tray modeling for Electrical & Instrument in PDS
Checking of Isometrics Drawing with P & ID
Extraction of screen dump using Design Review / Smart plant.
Clash Reviewing & System Clash Resolving of Piping with Piping/
Equipment/Structural.

R&D Facility for M/s Schering Plough Singapore. Phase I & II
Project and Responsibilities

Responsibilities – Piping modeling, Equipment modeling for TCM area
Cable tray modeling, conduits modeling and all electrical equipment
Modeling through PDS, 2D drawings extraction using PDS drawing manager
And PD draws. Inter discipline Clash checking, interdicipline co ordinate with Lead designers approved all False clash and re design for electrical routings.

Tamoil Refinery De- Collombey Foster Wheeler Italiana

Responsibilities – Piping modeling, Equipment modeling, Vessel trim for all
Equipments, Pipe rack inter-connection Checking and all 2D Dwg. Created through
Drawing Manager & Winterization Isometric checking & Column Piping and elevation Drawings prepare through 2d Pds


JOB ASSIGNMENT AT MALAYSIA

OIL LINE ENGINEERING & ASSOCIATES SDN (BHD)
No.2-2, Jalan SS 6/6, Kelana Jaya
47301, Petaling Jaya, Selangor Darul Ehsan, Kuala Lumpur, West Malaysia.

From January 15 1999 till May 2001 worked as PDS Designer.
From this company I am deputed to CHIYODA MALAYSIA SDN (BHD)
PDS Designer
February 99 to May 99 [3 months]

Project and Responsibilities
Project E.P.C.C. For Titan petrochemical (M) SDN. BHD
Cooling Tower and Raw water Area, Preparation of piping studies and Piping
Modeling in PDS. Isometric extraction using ISOGEN, Supports marking
And Bill of Materials

I was also deputed to BECHTEL MALAYSIA (SDN) BHD
PDS Designer
June 99 to Sept 2000
Project and Responsibilities

Was assigned to Optimal Chemical project a Derivative Facilities for Petronas / UCC
Integrated petrochemical complex, work involved in design Layout of piping
G A DWG preparation through pddraw and Equipment modeling, cable tray power
And control system Performed Cable tray Layout through Plant Design System using
Eeraceway modeling and Produced drawings through Pd draw and exportation to
Micro station SE produced Area Classification drawings using micro station. Responsible
For producing all piping dwg and cable tray layout, lighting and grounding plans using micro station and PDS Eeraceway modeling. Produced raceways tagging system for plan drawings and
Generated MTO in PDS for cable trays.

Preparation of process diagram and piping plan DWG’s using micro station SE and
PDS


TECHNIP, Malaysia
PDS Designer (Hvac Dept)
From October 2000 to May 2001.

Project and Responsibilities

South Pars Gas Field Development Phase I.

Piping Routing & Equipment Modeling for offshore platform, topsides and Facilities
Preparation of Small bore piping and plumbing using 3D PDS and Vendor Datas review
And client co-ordination.
Clash checking Resolved with inter Discipline and client review, using Smart plant.
Equipment layouts and Piping plan layouts extraction from PDS 3D to 2 D
Using drawing manager and micro station.
Checking of Isometric drawings with P&ID and Smart plant Review


PREVIOUS WORK HISTORY
Bechtel, India
Designer (Plant Layout and Piping)
May 97 – December 98

Project and Responsibilities
Project – Jamnagar Refinery Project Reliance Petroleum Limited, Jamnagar,
India. Marine Tank Farm, Refinery Tank Farms, Offsite and Utilities
Preparation of piping studies, Equipment, Piping Modeling and Small bore piping using PDS. Isometric extraction using ISOGEN supports marking, Sleeper Location Drawings using Drawing Manager & Micro station.

Deutsche Babcock Idea Ltd.
Chennai, India [ISO 9001 Company]
Senior CAD Draughtsman

Nov 1994 to April 1997

Project and Responsibilities

Job involved preparation of plot plans, Piping layout, Equipment layouts, Isometric drawings, Nozzle orientation drawings and Bill of Material etc. using AutoCAD Rel.13.
Project - P.T.SIAM MASPION POLYMERS, INDONESIA
Preparation of Equipment layout, Piping Layouts, Isometrics DWG, and Nozzle orientation drawings.

Project - 30000 TPA “MAN” MALAYSIA,

Preparation of Plot plan, Equipment layouts, Piping layouts Pipe rack drawings, Isometrics Drawings and Bill of Materials

Project – Reliance polyethylene ltd., India

Preparation of Plot plan, Equipment layouts, Piping layouts, Pipe Rack, Isometrics and Plan and Section Drawings.

M/S Esquire Engineers & consultants Ltd.

Chennai & Tamilnadu Newsprint and papers ltd, Tamilnadu

CAD Draughtsman

July 1992 to October 1994

Responsibilities

Preparation of Piping Layouts for steam and process lines Plan & sections drawings Piping supports, IBR drawings, Storage tanks & heat Exchangers.
M/S Industrial Fans, Chennai
CAD Draughtsman
August 1989 to 1992

Project and Responsibilities

Sponge Iron Limited, India

Preparation of detail & GA drawings for Dampers & Cement Plant Equipment, Belt conveyors and Slide Gates.

Kothagudam Thermal PowerStation

Preparation of details & GA drawings for Lubrication Oil Circulation System, Heat Exchangers and Support marking.

Mechanical Draughtsman
N.C.V.T Certificate
AUTOCAD Windows Re. 12, 13& 14
PDMS COURSE
CADCENTRE SINGAPORE
MECHANICAL-ELECTRICAL DRAFTING
NATIONAL TECHNICAL CERTIFICATE
GRADE THREE, ITE, SINGAPORE
SKILLED EVALUATION CERTIFICATE GRADE TWO IN MECHANICAL &
ELECTRICAL, ITE, SINGAPORE
PDMS ADMINISTRATION COURSE
AVEVA SINGAPORE
PDMS ELEC. STRU. HVAC 2D DWG. CREATION COURSE AVEVA SINGAPORE

I have good working experience on Computer Aided Design and Drafting
Ver. Reel. 12, 13, 14 and 2000.
Plant Design System SE NT Windows Ver. Isometric preparation through ISOGEN
Micro station V5 , SE V7 j ver. & V8
3DM (Bechtel Software 3D Design, for power project.)
PDS Modules for Piping Designer Equipment Modeling, Drawing manager, Isogen,
Electrical Raceway environment and Materials take for raceway through PDS.
Drawings Extraction from PDS drawing manger 3D to 2D using Pd Draw.

PDMS Pipe works, Equipment modeling. Certificate course from Singapore ITE.
Module I & II
PDMS Administration Course from AVEVA Singapore
PDMS certificate Course for Raceway, HVAC, Structural & Draft.

I have done 3D PDS and PDMS Modeling for Piping, Equipment, Electrical &
Instrument Raceway as well as 2D DWG for single line diagrams, process P&ID and
Equipment layouts using 2d pd_draw