CV Operation Technician (Control Room Operator)

Resume built for oil and gas job opportunities by a jobseeker with experience in Operation Technician (Control Room Operator) - would you like to offer this candidate a job/contract employment?

CV/Resume ID no.: 80068

Respected sir,

As I introduced my self and expressed the matter, I want to present my self as candidate for the post of ______________________________

Right now, I am working in Exxon mobil Asia pacific ltd.singapore as a control room Operator

I am having 12 years of Gas turbine, HRSG and Power generation equipment experience {10 MW to 180MW gas turbines.}

I hope you will consider me for the above-applied post.

If opportunity given I can do my best.

Thanks

Yours truly

Presently I am working in Exxon mobil Asia Pasifics ltd. Singapore .

Postion : Operation Technicians (Control room Operator)
DURATION : 1ST April to till cont.
JOB ONUS & :
DESCRIPTION

 Gas Turbines:
 GE Frame 6B machine which is having Mark V control system 2* 80 MW each with Combined cycle operation.
 Hrsg with supplementary (140 t/hr each & pr. 100 kg/cm)
 Boiler (oil and gas fired)*2 (160 t/hr each & pr.100 kg/cm2)
 Waste water treatment plant
 Spent caustic unit
 Demin water plant
 Partial oxidation unit (using a tar , steam and 100% oxygen and producing syng. Gas)
 Tank farm area ( Tar tank, naphtha tank)
 Cooling tower

Prepared working permit , safety auditing, confined space work permit

Training : special training done for fire fighting ,confined space entry, work permit
Safety related training.


# At present I am involved in project work like line tine in job and looking and preparation to install gas tubring frame 9E.


Total experience with Combined Cycle power plant is: 13 years (Including 3 year training)
Work Experience: Since Feb 1998 GE Nuovo Pignone Ahmedabad
C/o CCPP Arvind Mills Naroda.
At present I am working and having past experience with the following equipment such as startup, shutdown, Isolation, desolation etc.

 Gas Turbines:
 GE Frame 6B machine which is having Mark V control system *2 with Combined cycle operation.
 Heat recovery steam generator Thermax make with working pressure 42kg / Cm2.
 Steam turbine with the generation capacity up to 110 MW
 110 MW thermal power station boilers where I worked as trainee for 3 years.
 GE Nuovo Pignone makes gas turbine PGT 10 which is being used for combined cycle and cogeneration operation.
 Thermax make RO water system which is being used for Combined cycle plant
 Gas turbine equipped with air inlet cooling system and steam injection system.
 I am having experience with working with DCS such as Tata Honeywell, Fuji, SCADA,TDC-2000 etc

PAST EXPERIENCE : Worked as “Power Plant Control Room Operator” at
Combine Cycle Power Plant of Ahmedabad Electricity Company

Duration : July 1996 to Feb 1998 to 30 june 2007

Job Profile Involved in Operation in 2 No. Frame – 6 Gas Turbine OF 32 MW Each & Also involved in GT Related operation as well field as well in Control Room to Operate Mark –IV Panel.
 Steam Turbine Capacity 32 MW
 HRSG 2No. 60-TPH each
 Maintain Generation reading & all reports.



JOB ONUS &
DESCRIPTION : Was involved in Project right from zero date participated in
Various activities at different levels.
 Actively involved in erection and commissioning and participated in various activities at different levels. As senior Operator (D C S)
 Involved in erection and commissioning of GAS TURBINE, Cooling Water System, Air Compressors, Liquid Fuel handling System, etc.
 Participated extensively in Mechanical and pre-commissioning activities of Process steam piping and HRSG Alkali Boil out, Safety valve floating Etc.
 Actively involved in pre-commissioning activities of STEAM TURBINE like condenser vacuum test, Ejectors, Condenser Dumping, and STG Rolling Etc.
 Also have involved in GT online & off line Water/Chemical Activity.
 Start up , shutdown of Gas turbine, HRSG,& Steam Turbine
 Operation and monitoring parameters of its related auxiliaries.
 Trend Analysis; prepare shutdown and normal stop reports, daily report etc. Operation and monitoring of parameters of auxiliaries. Fuel handling and Transfer system , cooling water system , Electrical system, Mark-V control system for, DCS ABB mode system for and its related auxiliaries.

SPECIAL TRAINING: Special training received while unloading Naphtha system with
GE Norms like EHS (Environment Health & System) & LOTO (Lock out
& Tag Out)

INVOLVEMENT : Being a team member of operation & Maintenance team
Suggested Many Modification, & Involved in such Implementations Also
Preparing S.O.P & Log Books & M.H.D. Reports.

Educational Qualification

 Diploma in Mechanical Engineering passed from Technical Educational Board. Gujrat, India.
 First class Boiler Competency passed from Government of Gujarat in April 2000.
 NCTVT examination passed from The Ahmedabad Electricity Co ltd, followed by 3 years training for the Power plant & rotary equipment operation. Equipment such as Gas turbine, Gas compressors, Diesel Engines, Steam turbine, RO water plant, DM water plant, desalination, Air compressors, etc.

KNOW INTERNET, EXCEL, WORD, MS OFFICE

PLAYING CRICKET