Bachelors in Mechanical Years of Experience:
Authorized to work in: Pakistan, Saudi Arabia Present Location: Saudia Arabia, Al Khobar Relocation: Brazil, Oman, Russian Federation
1. Summary (Cover Letter) - CV/Resume Part 1 [Mandatory]
I start my profession after successfully completion DAE (Mechanical) with good safety manner in Oil and Gas Development Company Ltd (Pakistan) as an Assistant Technician Mechanical from 2000 to Date worked on Mechanical, PCR, SCR, Work Over and Heavy Rigs familiar with Kelly, Top Drive System(Varco TDS 11S),Horizontal, Directional Drilling, Exploratory,Underbalance Well.
Full command on Computer, MS Office, Excel other operating software’s
2. Work Experience - CV/Resume Part 2 [Mandatory]
June 2008 I am working on VFD Deep Drilling Rig.
2005 To June2008 Rawabi Dalma Co Ltd Kingdom of Saudi Arabia contract with Saudi Armco as Rig Mechanic designation to complete overhaul the rig in yard detail is below
• Manage Rig Operation in Safe Manner according to Company and Client policies & procedure
• Supervise and plane Rig Moving.
• Play active roll in QHSE meeting, tool box talk, stop card, PTW implementation and Emergences.
• Keep rig equipment in operational condition as regulatory and safety requirement.
Nov2005 overhauling the rig in Yard Khobar.
• Draw Works National 110-UE (1600HP)completed Overhaul,
Alignment Both DC Motors 800, Elmagco, All chains Replaced with new. Main High, Low clutch’s replace. Inspected Bearing Clearances
• Rotary table: clutch and brake drum replaced. Check bearing clearances
• Mud Pump: Model 10P130 (1600HP) inspected and MPI crank and other major equipments. Wear Plates, Cross Head.
• Koomey Unit Completed Overhaul.
• Sheaves. Dismantle and Assembled all cargo Sheaves.
June 2006. Upgrading the rig in (Udalya).
• Replaced Major engines Cat D398 with Cat 3512 EMFI.
• Varco TDS 11S installed with assist the Varco Specialist.
• Rotary table independent drive system
• All centrifugal pumps replaced with mechanical seals Harrisburg Pumps.
• Install the New Blow Out Prevented System PLC System made by SARA
• Installed new Agitators and Breathing compressor MAKO & air line system.
• Replaced Elmagco and Alignment with Draw Works
2002-2005 Oil and Gas Development Company Limited, Pakistan Largest Company as
Rig Technician Maintenance (Rig Mechanic) deep drilling rig National 2, 3600 HP & 19000 Feet I done related to maintenance of Rig as well as all equipments.
Draw Works C2 Type II Continental Emessco (1600 HP) ,Mud Pump FA 1600B (1600 HP) Emessco, Blow Out unit Koomey Type 80,Rotary Table chain drive, Primary Source 05 Engines CAT D 398 (910 HP) each. Manage rig operation in safe manner according to company and client Policies and procedure. Prepare to preventive maintenance and ready for all Emergencies.
2001-2002 Oil and Gas Development Company Limited, Pakistan as Assistant Technician
Maintenance (Assistant Rig Mechanic) on Romanian mechanical Work over Rig 500 HP & 300 feet with 4 Drill Pipe. I responsible all Maintenance/Repair work and all office work related to maintenance on Work over Rig. Replaced Rotary Main Bearing, Traveling Block Bearing and also change floor main engine Vola 5DvSra (polish) 500 HP.
2000-2001 Oil and Gas Development Company Limited, Pakistan as Assistant Technician Maintenance (Assistant Rig Mechanic) first successfully completed the training in Oil and Gas Training Institute I-9 Islamabad Pakistan after Completion training posted me on Heavy Deep Drilling Rig National 2, 3600 HP & 19000 Feet. I am too in CAT D398 major overhauling team.
3. Education & Training - CV/Resume Part 3 [Mandatory]
1993-1995 Secondary school certificate In 1st Division
1996-1999 Diploma of Associate Engineering (D.A.E) Mechanical in 1st Division.
1996: Auto CAD- 2D Course.
1997-1998 One year Diploma in Mechanical Draftsman
2003-2005 Bachelor of Arts in 2nd Division
4. Computer Skills - CV/Resume Part 4 [Mandatory]
MS Office, MS Excel
No Problem operating any type Of Software.
5. Other Skills - CV/Resume Part 5 [Optional]
Passed Special Maintenance Courses from
Oil and Gas Training Institute, Islamabad. Pakistan
• OIL AND YOUR ENGINE CAT D398B
• FAILURE ANALYSIS OF TURBO CHARGER CAT D398
• INTRODUCTION TO SLUSH PUMP FA 1600
• OPERATION AND MAINTENANCE of EMSCO PUMP FA 1600
• FA 1600 SLUSH PUMPS Valve And Seats
• CATERPILLAR D398 FUEL SYSTEM
• MS EXCEL/MS WORD/Window 98
• DERRICK SOLID CONTROL COURSE (OIL TOOL INTERNATIONAL, Islamabad)
6. Additional Information - CV/Resume Part 6 [Optional]
1. H2S Rig Site 2. PTW Procedure
3. Work Permit Procedure 4. Safety Induction 5. Mechanical Lifting 6. Hazardous Material Handling 7. Personal Security 8. Work Shop Safety 9. Lock Out Tag Out 10. Fire Fighting